Canal Winchester, OH

Performed furnace check on Lennox furnace. Customer had inspector list issues that needed address. Inspector noticed water leaking onto condensation line. Water leaking from suction line having roughly 1 inch of uninsulated pipe. Was able to manipulate insulation to cover line completely. Customer also had concerns with calcification and rust on burners inducer motor and flue pipe. Parts on order, should receive parts within 3-7 business days. Will return when parts arrive to replace corroded parts. 3 ppm co in flu. 10 %o2. Cleaned flame sensor. Will return as soon as possible to make corrections Returned to complete furnace repair. Replaced burners, inducer motor/adapter and flu pipe. Started furnace to confirm operation and saftey. Unit running with 7.2o2 68 degree deltat. No issues upon departure.

Cost to install central air conditioning and furnace. Cost to install humidifier

Cost to install air conditioning

Cost to install air conditioning and furnace

Performed yearly maintenance and safety checks on 19 Bryant ac.replaced 12-24-1 filter. 35/5 voltage absorption system reading 34/5. 70 in Rush amps. No issues found at this time.

Performed yearly maintenance and safety checks on 2000 Rheem air-conditioning system. Found 45/5 orange absorption system reading 45/5. 83 in rush amps. No issues found at this time. Clean 213 filter.

Performed yearly maintenance and safety checks on 13 trane ac system. Found 35/5 reading 34.1/4.9. 88-108 hard start reading 104. No issues at this time 52 degree ambient temperature.

Performed yearly maintenance and safety checks on 2011 Lennox air conditioning system. Found 45/10 voltage absorption system reading 45/10. 67 inrush amps. 88–108 hard start reading 104. Cleaned condenser. Replaced customer supplied 18254

Ac check 2012 Bryant 45/5= capacitor. Filter 16-25-1

Performed yearly maintenance and safety checks on 22 AC system found 35/5 voltage absorption system reading 35/5 found 48 in Rush amps. Replaced 1625 one filter no issues found at this point in time.

Responded to no heat thermostat calling for heat. 66 in home 73 set temperature. Found code 32 for pressure switch found inducer pulling 0-3 inWC customer has exterior of home being panted. Painters covered up concentric kit not allowing proper exhaust. Removed cover per customers request to restore heat. Furnace cycled on properly without fault. 0 ppm co in supply. Dirty 16254 filter. Replaced 10/15. replaced customer supplied filter. No further issues.

Returned to repair. Replace blower motor and control board. Further diagnostics found identity chip faulty no allowing proper communication with blower motor. Replaced chip furnace cycled on properly. Running with 11%o2. 14 ppm co in flu. 0 ppm co in supply. 46 degree dletat. No further issues at this time.

Called in morning to quote for repair blower motor power choke and possible board. Replaced blower motor. New motor has different wiring connections as well as smaller plug not able to be used power choke also not able to be connected. No paperwork with blower. When installed blower would not operate from board. Will need to double check parts Monday and require at that point.

Annual maintenance check on a rheem air conditioner

Upon arrival customer stated it had started running. Found furnace running. Cycled furnace several times to find no fault occurring. Found charred/weak flame sensing system. Presented options hm15a-e. Customer chose option a. Performed repair and cycled furnace. System running with 10.5% o2. 12 ppm co in flu. 0 ppm co in supply. 45 degree deltat clean 16251 filter. Found floor drain to be clogged advised may want plumber to look at drains. Strong Oder coming from drain.

Performed  yearly maintenance  and safety checks on 2020 Bryant furnace in attic. Furnace is running with 10.1%o2. 9 ppm so in flu. 49 ohm igntion  system 45 degree dletat. Furnace cycled into second stage properly.system running with 7.5%o2. 33 ppmco in flu. 0 ppm co in supply. Cleaned flame sensor. Customer maintains 16254 filter. Also performed yearly maintenance  and safety checks on 20 Bryant furnace in basement. Previous  technician mentioned excess noise in motor. Found noise to be associated  with airflow in filter cabinet. After Removing filter noise stops. Furnace running with 12.4%o2. 20 ppm co in flu. 34 degree deltat. Furnace cycled into second stage properly.  Running with 7.5% o2 48 ppm co in flu. 0 ppm co in supply.  50 degree deltat.

Thermostat indicating call for cooling. Found code 3 for pressure switch stuck open. Reset control board. Made call for heating. Found inducer motor having issues running. Motor not seized. Seems as if something holding wheel from spinning removed motor to loom for critters. Founs bead of caulk stuck around blower wheel. Attempted to remove foreign object Unsuccessfully messed with wheel to try to free motor. Cannot remove object. Called for pricing and Availability for motor and pressure switches. Not in stock. Presented hm7 with possibility of returning for repair Tuesday or Wednesday cust9mer not ready for repair and will call next week to schedule repair.

Performed yearly maintenance and safety checks on 1998 Bryant furnace. Found dry bearing noise associated with inducer. Found ignition system reading 90 ohms. Also found voltage absorption system outside manufacture specifications.customer wants to wait issues out and address when fault occurs also Performed maintenance on 2017 rheem furnace. Found 40/5 voltage absorption system reading 40/5 cleaned coil. No concerns at this time.

Completed annual maintenance on a 2021 comfortmaker furnace. And during testing of the unit the technician found no electrical protection device, the air filter to be installed incorrectly, and ductwork to have large amounts of dust/hair build up. Customer not interested in electrical protection device at this time. Technician left fresh air corporation information for duct cleaning, as well as iwave information for air cleaner. Customer may call back at a later time for the install. Technician left filter beside unit as filter has recently been changed, and created inspection hole for combustion analysis. No issues at time of departure.

Completed annual maintenance on a 2021 comfortmaker air conditioner. During testing of the unit, the technician found no electrical protection device and the outdoor unit to be very dirty. Technician explained this would cause issues for the unit to keep up. Customer not interested in electrical protection device today. Technician left air filter beside unit as filter had been recently changed. No issues at time of departure.

No cool on a 2019 comfortmaker air conditioner. Upon arrival technician found voltage enhancement system to be dead on both sides, as well as outdoor unit to be very dirty. Technician presented options Hn13a-e. Customer chose option B. Technician replaced voltage enhancement system and installed electrical protection device. Technician cycled unit successfully after repairs were completed. 18° temperature split. No issues at time of departure.

No cool on a 2019 comfortmaker air conditioner. Upon arrival technician found voltage enhancement system to be dead on both sides, as well as outdoor unit to be very dirty. Technician presented options Hn13a-e. Customer chose option B. Technician replaced voltage enhancement system and installed electrical protection device. Technician cycled unit successfully after repairs were completed. 18° temperature split. No issues at time of departure.

Replaced failed capacitor on a Carrier air conditioner

Cost to replace air conditioning. Price to install new air conditioner.

Completion Notes: Edit Completion Notes Made call for cooling upon arrival. Replaced customer supplied 16251. Found-2.5 psi in system. Advised moisture has been introduced into system and may seize compressor. On schedule for quote today 12-1.